50% off your first credit pack

See prices →

Guides · 4 min read · · Amberleak Editorial

How to make a stencil: design, cut and paint

A good stencil starts with the design: bold shapes and bridges that hold the pieces together. How to design, cut and use stencils on walls, fabric and wood.

A motorbike photo turned into a cut-ready stencil with connected shapes

Stencils are one of the oldest ways to repeat an image: on walls, T-shirts, tote bags, signs, furniture, cakes and street art. The idea is simple. Cut holes in a sheet, then push paint through them. The skill is in the design, because a stencil can only have two states: open or closed.

1. Understand how stencils work

Every part of a stencil design is either a hole (paint goes through) or solid (paint is blocked). There are no greys, no gradients and no soft edges. Tones are made by choosing which areas are black and which are white.

The biggest beginner mistake is the "floating island". Think of the letter O. Cut out the ring and the middle piece falls out, leaving a solid blob. To keep the middle in place, you need small connecting strips called bridges. That's why stencil letters have little gaps in them.

2. Design for cutting

A good stencil design has:

  • Bold, simple shapes. Fine details are hard to cut and paint bleeds under them.
  • Two or three tone levels, turned into solid black areas. For example: shadows black, everything else open.
  • Bridges for every island: eyes, the inside of letters, gaps between fingers.
  • A minimum feature size. For hand-cut stencils, avoid shapes and bridges thinner than about 2–3 mm.
  • A border of at least 2–3 cm of solid material around the design, so the stencil holds together and paint doesn't escape.

Making a stencil from a photo

You can trace a photo by hand: print it in high contrast, put tracing paper over it, and outline the darkest areas. Then fill them in, add bridges, and simplify.

A faster route is the stencil generator. It turns a photo into a clean stencil design: bold, flat black shapes on white, two or three tone levels, crisp edges, and small bridges so every inner piece stays connected. The background is dropped, and the subject keeps its pose and proportions.

A portrait turned into a bold black-and-white stencil
A portrait turned into a bold black-and-white stencil (before)
BeforeAfter
A portrait as a two-tone stencil, ready to cut.
Stencil generatorTurn a photo into a cut-ready stencilTry it with your photo

Choose photos with strong light and shadow from one side. Flat, evenly lit photos have no shadows to turn into shapes. Profiles, animals, vehicles and objects with clear outlines work best.

The simplest stencil: a silhouette

For a one-shape stencil, a silhouette is the easiest design there is: one solid outline, nothing inside. The silhouette generator turns a photo of a person, pet or object into a crisp black silhouette on white. Cut along the outline and you have a stencil with no bridges at all.

3. Choose your material

  • Paper or card: fine for one or two uses with spray paint. Cheap, easy to cut, quickly ruined by wet paint.
  • Freezer paper: ironed onto fabric, it sticks temporarily and peels off cleanly. A favorite for T-shirts.
  • Acetate or Mylar sheets (about 0.1–0.2 mm): reusable, washable and transparent, so you can position them easily.
  • Adhesive vinyl: sticks to walls, glass and wood for very sharp edges. Single use. Great with cutting machines.
  • Thin plastic folders: a cheap substitute for Mylar.

4. Cut it

By hand

  1. Print the design at the final size.
  2. Tape it over your stencil material on a cutting mat.
  3. Use a sharp craft knife with fresh blades. Change blades often; a dull blade tears.
  4. Cut the small, inner details first, while the sheet is still stable.
  5. Turn the sheet, not your hand, around curves.
  6. Don't cut through the bridges.

With a cutting machine

Cutting machines like Cricut or Silhouette cut vinyl and card from a digital file. Convert the stencil design to a vector (most machine software has an auto-trace function), check that all bridges survived, and cut. This is the best route for lettering and repeated designs.

5. Paint without bleeding

  • Secure the stencil. Use repositionable spray adhesive, painter's tape, or vinyl. Gaps under the stencil cause bleeding.
  • Use less paint than you think. A nearly dry brush or a light spray coat gives sharp edges.
  • Dab, don't brush. Use a stencil brush or sponge with an up-and-down motion. Brushing pushes paint under the edges.
  • Spray from 20–30 cm, in several light coats, perpendicular to the surface.
  • Lift straight up when the paint is touch-dry, not fully dry, to avoid peeling it.

On fabric

Use fabric paint or screen printing ink. Put cardboard inside the shirt so paint doesn't soak through. Heat-set the paint with an iron after it dries, following the paint's instructions.

On walls

Use a level and light pencil marks to position repeating patterns. Painter's tape around the stencil protects the wall. Test the paint on a hidden area first.

6. Multi-layer stencils

For more color, make one stencil per color and paint them in order, from lightest to darkest. Add registration marks (small triangles or crosses in the corners) on every layer so they line up exactly.

Ideas to try

  • A pet portrait on a tote bag.
  • House numbers on a fence or mailbox.
  • A logo on a batch of shirts for a team or event.
  • A repeating pattern on a plain wall or furniture.
  • A portrait stencil for a birthday sign.
  • A cake decorated with powdered sugar through a paper stencil.

Stencils also make great tattoo references, since the shapes show how a design reads in solid black. Our guide on designing your own tattoo explains how to use them with an artist.

Start small, cut carefully, use little paint, and you'll get clean results from the first try.

Tools in this guide

More from the blog